|
|
Post by tokejo on Feb 16, 2014 16:32:27 GMT -5
I found that out, but at least I now know that the final band is the tolerance %. I'll take these to work and measure them with a micrometer.
|
|
|
|
Post by mastertech on Feb 16, 2014 16:36:36 GMT -5
The resistors you bought for the last receiver, what wattage were they? It should be on the package.
|
|
|
|
Post by tokejo on Feb 16, 2014 16:44:39 GMT -5
Thanks.
|
|
|
|
Post by tokejo on Feb 16, 2014 17:05:09 GMT -5
Those were all 1/4 watt, which looks like R545 is. I can't tell what R554/R555 and R561/R562 are, if they are 1/2 or 1W.
The body of R545 is red, if that matters.
|
|
|
|
Post by tokejo on Feb 16, 2014 18:09:35 GMT -5
N113136647820-IL is the part # for R554/555/561/562, but I can't find any info about it.
|
|
|
|
Post by mastertech on Feb 16, 2014 18:34:33 GMT -5
I have a VSX70 here so I looked up the part number for these and they are the same number. So looking at these resistors they are slightly larger then 1/2 watt but smaller then 1 watt. But 1 watt looks like they will fit fine for clearance. You could order both 1/2 and 1 watt and if the 1/2 watts are the exact same size then you could use them. But if they are even slightly smaller I would not. It is fine to go larger but not smaller. These can be a basic flame proof resistor.
The red case resistor usually means it is a metal film resistor. So that's what I would put there.
|
|
|
|
Post by tokejo on Feb 16, 2014 20:01:34 GMT -5
1 2SB1560-ND TRANS PNP AUDIO/GP MT-100 TO-3P
1 2SD2390-ND TRANS NPN AUDIO/GP MT-100 TO-3P
4 P0.47W-1BK-ND RES 0.47 OHM 1W 5% AXIAL
4 A105967CT-ND RES 0.47 OHM 1/2W 5% AXIAL
2 100DSCT-ND RES 100 OHM 1/4W 5% AXIAL
|
|
|
|
Post by mastertech on Feb 16, 2014 20:28:46 GMT -5
Looks fine as long as you are comfortable not ordering extras just in case.
|
|
|
|
Post by tokejo on Feb 16, 2014 21:42:21 GMT -5
I figured that if I needed extras I would include them in the order for the next receiver.
|
|
|
|
Post by mastertech on Feb 16, 2014 21:49:54 GMT -5
Ok, good idea.
|
|
|
|
Post by tokejo on Feb 19, 2014 16:44:31 GMT -5
Parts will be here Friday and I should have time to install after work.
*Fingers crossed*
|
|
|
|
Post by mastertech on Feb 19, 2014 18:29:13 GMT -5
Great. Keep us updated.
|
|
|
|
Post by tokejo on Feb 21, 2014 22:28:35 GMT -5
Parts arrived. Probably have time to start on this tomorrow.
|
|
|
|
Post by mastertech on Feb 22, 2014 10:45:28 GMT -5
Great. Keep us updated.
|
|
|
|
Post by tokejo on Feb 24, 2014 23:00:23 GMT -5
Fixed.
Need to run it through it's paces, but with 1 speaker attached and the Tuner, I have sound.
The 1W resistors I bought seem a little small, but the 2W resistors I bought for the Denon are WAY bigger.
|
|
