Reply

Running A/V equipment from a stand-by generator.

« Prev
1
Next »

howie
Junior Member

Posts: 88

Running A/V equipment from a stand-by generator. Feb 14, 2016 15:46:01 GMT -5

Quote

Post by howie on Feb 14, 2016 15:46:01 GMT -5

I am right now breaking in a new generator. Manufacturers instructions say 3 hrs no load break in. Out of curiosity I decided to check no load Hz
While it is running and am showing 64 HZ. I plugged a couple of things into it and it dropped to 62.5. How far off 60 Hz can I go without damaging A/V equipment? I know I can adjust the governor down a bit but am curious what is worse, below 60 or above? I'm anticipating 50-60 percent load so the generator should have no problem

Casethecorvetteman Master Tech Posts: 1,219	Running A/V equipment from a stand-by generator. Mar 23, 2016 17:43:00 GMT -5 Quote Select Post Deselect Post Link to Post Member Give Gift Back to Top Post by Casethecorvetteman on Mar 23, 2016 17:43:00 GMT -5 Shouldnt really be an issue, fully loaded should be very close to 60Hz

Casethecorvetteman Master Tech Posts: 1,219	Running A/V equipment from a stand-by generator. Mar 23, 2016 17:43:50 GMT -5 Quote Select Post Deselect Post Link to Post Member Give Gift Back to Top Post by Casethecorvetteman on Mar 23, 2016 17:43:50 GMT -5 What size is the generator and what are some specs on it?

Shoutbox

albertto: Hi everyone. This is my first post here, so greetings to everyone. I hope to help and get helped in my diy prjects or other stuff. Thank you in advice!! Nov 2, 2024 12:45:30 GMT -5 *

madmal: Hi where did you source your D808K013DPTP4 from ? Oct 10, 2024 9:04:46 GMT -5

zerolearner: Hi team members I'm new to the forum. I have denon X2000 firm issue I replaced the new ADSP IC but upload the firmware via USB port I got a error message connection failed 5A. FLAG0 present 0.84V is there any JTAG programmer for update the firmware. Sept 30, 2024 22:36:28 GMT -5

viburnum: onkyo 1010 Sept 28, 2024 7:04:21 GMT -5

redpill: Would you able to provide more details in regards to your fix. Did you replace faulty unit or fixed yourself? I'm having similar problem and wonder how to approach it. Thanks. Lucas. Sept 8, 2024 1:10:29 GMT -5

redpill: Hi Tom, Sept 8, 2024 1:05:26 GMT -5

waiyan: Please help me,my Yamaha RX-V671 no power,no red led, no clip relay . If you free guide line me😊 Jan 31, 2024 12:11:10 GMT -5

retiredhvac: Onkyo TX-SR353 Service Manual Request. Tried to contact forum member who offered it but no reply. This unit may share identical traits with a Pioneer.

Sept 16, 2023 16:02:07 GMT -5 *

mastertech: Not finding much. Maybe get the part numbers off those 2 devices mounted on the heatsink near that resistor. Sept 15, 2023 21:03:01 GMT -5

Sept 15, 2023 6:44:08 GMT -5

dirty666: Hi mastertech, here are better fotos. I hope you can help me

Sept 15, 2023 6:43:42 GMT -5

i.postimg.cc/c6fG0L1Q Sept 15, 2023 6:41:16 GMT -5

Sept 11, 2023 13:41:19 GMT -5

Sept 11, 2023 13:31:59 GMT -5

Sept 11, 2023 13:31:00 GMT -5

Sept 11, 2023 13:30:21 GMT -5

mastertech: Can you post a picture of the entire back side of that board? Sept 10, 2023 18:39:49 GMT -5

dirty666: It is R23 on the platine Sept 10, 2023 7:07:25 GMT -5

Sept 10, 2023 7:00:50 GMT -5

dirty666: Here are some Pictures Sept 10, 2023 7:00:02 GMT -5