|
|
Post by vietson on Jan 13, 2014 2:17:24 GMT -5
When I plugged in SC25 Standby bright blue light on. but the display does not work. Wan to turn it off. I press the Standby 10s it off .when I press the Stanby to turn, on display SC25 appears POWER ON and are not active. I tried unplug and plug back and hold Stanby 10S it off. Once turned on,the display SC25 appears POWER ON. and buttons and remote are not working. I cant' reset as guide SC25 I use these speakers are 8 ohm. Did not examine the entire matter. I suggest detailed step by step guide to fix this situation. I was in Hanoi Vietnam PIONEER service pack, but they do not know what to do with PIONEER Elite SC25. because they have not seen it ever. I appreciate your help ( my situation í that many people encounte (on http//avsforum.com) but I do not see how to solve it.
I have mail for USA PIONEER ear because they help, but they said they can not be guided through the mail, they bring to the USA proposal to fix, but for me it is not possible. I also came to Vietnam by Pioneer Services of repair but they can not ever SC 25.I do not know how to fix it, wish he guided me step by step details to check and repair
thank you.
Vietson email: vietson2457@yahoo.com.vn
|
|
|
|
Post by mastertech on Jan 13, 2014 13:08:07 GMT -5
The fact that you see "power on" indicates the display is working. That fact you can turn it on and off indicates that part is working. So 2 things first off.
1)Do you have the remote so you can check if the display is just dimmed down to off?
2)When it is on and the blue standby is on, are there any blinking leds?
3)Try a master reset. While receiver is off, press and hold the enter button and while holding it also press the on button and see if it turns on and says "Power on" then "reset <NO>". Release buttons as soon as it turns on. If it does then hit right arrow so it says "reset" then enter, says "OK" hit enter. It should say "ok" again and then shut off. Done.
|
|
|
|
Post by Admin on Jan 13, 2014 13:37:09 GMT -5
We would appreciate it if you would register with our forum. We may eventually change the status to this requirement in order to post. Plus we would like to increase our member base.
Plus it helps to deter spamming. I have recently allowed some spamming to remain but this may also change in the future.
Thank you.
|
|
|
|
Post by vietson on Jan 14, 2014 8:31:31 GMT -5
Thank.
I unplug it and then plug StanbyOn hold back, StanbyOn bright blue lights on, no display at all. I StanbyOn press and hold the green light on StanbyOn 10s off. I press and hold and press Enter again Stanbyon POWER ON appears on the display. Then all the buttons on the front panel and remote control are all not working but I have not checked Dimmer do it. When reiceiver in standby mode, can be turned on by remote and on display have POWER ON. All the lights are flashing none. Only Stanbyon bright lights on and the POWER ON light.
please help me see his next check how to start inside it.
Thank you very much
|
|
|
|
Post by mastertech on Jan 14, 2014 15:30:07 GMT -5
Wish the translator was working a little better. It is not real clear on some parts.
Even if the display was dimmed to off it would still show a normal display for around 2 second after it shows Power ON. Since it appears as though you do not have that then my next guess is that you are missing a power supply some where.
Do you have a DMM and are you able to test, solder and understand directions on where to test?
|
|
|
|
Post by vietson on Jan 14, 2014 19:24:42 GMT -5
Thank you.
When POWER ON current screen, I press and hold it for 10 seconds Stanbyon it off, if it does not appear that any of the matte screen does. If the press Stanbyon (reiceiver on the front or on the remote), the display appears bright POWER ON. does not have a flashing light.
Can you tell me step by step inside reiceiver test, where to start, if it is not broken, the section continues where he let me know a workflow reiceiver SC25 test this, so I'll ask a technician inspect me. you please help me to technicians inspect it according to his instructions.
Thank you
|
|
