|
Post by tokejo on Mar 12, 2014 21:25:15 GMT -5
All those points were on the bottom of the board so I had to remove it from the chassis. The HDMI points are also on the bottom, nearly impossible to get to that point if I have to put it back in and plug everything back together.
A DMM isn't something I use very often so this is new to me.
|
|
|
Post by tokejo on Mar 12, 2014 21:19:33 GMT -5
Does the board need to be put back in the receiver and plugged in?
|
|
|
Post by tokejo on Mar 12, 2014 21:02:53 GMT -5
R7288 = 0.3 Ohms R7289 = 0.4 Ohms R7290 = 0.2 Ohms R7291 = 0.3 Ohms R7292 = 0.4 Ohms R7293 = 0.2 Ohms R7294 = 0.2 Ohms R7295 = 0.1 Ohms
I'm unsure how I voltage test that point. Does the board need to be put back in the receiver and plugged in?
5V AC? Which ground should I use?
|
|
|
Post by tokejo on Mar 12, 2014 19:38:35 GMT -5
I've changed the setting on CBL/Sat from Auto to HDMI and back, no change. I think I changed it from Opt to None as well. Regardless when it's plugged in I get no change from the front panel, like PCM or Dig(ital).
Dinner time, I'll check those points before I turn in.
|
|
|
Post by tokejo on Mar 12, 2014 19:12:20 GMT -5
I never even noticed the front HDMI.
The front HDMI works. Tried CBL/Sat again, still doesn't work.
|
|
|
Post by tokejo on Mar 12, 2014 18:55:59 GMT -5
D7212/D7213 - OL/OL D7214/D7215 - OL/OL D7216/D7217 - OL/OL D7218/D7219 - 803/OL
|
|
|
Post by tokejo on Mar 12, 2014 18:15:54 GMT -5
Congrats Nash/Mac. Nice work.
|
|
|
Post by tokejo on Mar 12, 2014 17:48:50 GMT -5
D7212-D7223 - only solder pads, no diodes
R7254 - 50.9 Ohms R7255 - 50.6 Ohms R7266 - 5.3 Ohms R7267 - 1.78K Ohms R7268 - 1.79K Ohms R7274 - 0.4 Ohms R7275 - Solder pad
C7256 - Good C7255 - Good
I also checked C7260 - Good, C7259 - Good, L7209 - 0.2 Ohms
|
|
|
Post by tokejo on Mar 11, 2014 21:57:44 GMT -5
Had family over tonight, I'll work on this tomorrow.
|
|
|
Post by tokejo on Mar 11, 2014 18:44:03 GMT -5
Blu-Ray player plugged into Blu-ray input on Receiver. Receiver is outputting sound from the blu-ray.
TV is on, HDMI cable connected to it, but not to the receiver.
Plugged HDMI cable into HDMI Out of receiver, sound cut out for about half a second. No video, waited about 60 seconds. Pulled HDMI and reinserted, sound did not cut out this time, still no video.
The whole time the TV displays "No Signal"
|
|
|
Post by tokejo on Mar 10, 2014 21:59:20 GMT -5
HDMI audio works via DVD and Game, it does not work via CBL/SAT. The Dig. and PCM icons do not light up like with the other three HDMI inputs.
From what I can tell, all setting are correct.
|
|
|
Post by tokejo on Mar 10, 2014 21:46:13 GMT -5
2. Optical input works 3. Analog monitor works
Tested both with Xbox 360.
HDMI sound works via Blu-Ray input. Checking the other three now.
|
|
|
Post by tokejo on Mar 10, 2014 21:30:46 GMT -5
Good. 1)How about the tuner? 2)Also, do you have a way to test the optical and coaxial inputs? 3)I believe you said the analog monitor worked, correct? I am trying to make sure that it is only the HDMI section where the problem lies. 1. all good 2. optical yes, coaxial might be tough 3. Analog monitor worked on the other board, haven't tested this one yet.
|
|
|
Post by tokejo on Mar 10, 2014 21:21:54 GMT -5
Tuner works on all four channels.
|
|
|
Post by tokejo on Mar 10, 2014 19:56:48 GMT -5
No luck via HDMI out only, no menu display.
|
|